Toshiba TC183G22AF

On sound board:
PS/2 port
CS4232-KP
YMF262
5x 100 6V SMD 6mm radius
ALPS-J v2.5 3DA3DA272A BU3887 621
TOshiba 187HP C1995 226 623106

Removing the sound board:
Pull up on the main connector
The ribbon cable retainer FLIPS UP, not pulls out like most others.

Modem inside: AT&T 1634T48, AT&T C882-29V-5 SL1832, AT&T VALV34T, AT&T T 7525 EC, Toshiba TC183G17AF, board: 6710, KS-112 ; M5M5256BVP 70LL, AMD flash, labeled F36000 323009

2 NIMH batteries; 1 6-cell P71007004032, 1 3-cell P71007006012

mic is in front right
another smd cap on mainboard

Mainboard: 2 screws near rear (1 on outside), 1 in power module, pops up
Toshiba TC183GT6JF 7111
NEC D78P014YGC (or D70, D76?)
CHIPS F65550 TM3351C
Toshiba TC183G22AF
Toshiba P45002232011
4x Toshiba TC514265DJS-50
caps on underneath of mbd: 3x 330uF 6.3V, 2x 120uF 16V

MC2563A

CPU fan- DC Brushless UD0FB2E02 5V 0.07A 6122

- Sound module
- CPU heatsink
- PCMCIA slots
- Shield, Mainboard
- CPU board


Bottom of mbd:
RAM
Toshiba TC200G70TB (big chip)
Toshiba T7K72-05
2x Toshiba F7320Y TC55V1325FF-8
Toshiba TC55V328AJ-15
Toshiba TC163G59AF
CY2254ASC-2
CY2292SC-12
4x Q S32X245Q2
Maxim MAX213CAI
AMD flash chip sticker F36000 36403

Fan into housing area, plug under CPU board.
Plate on bottom of CPU board, 2 screws.  1 screw underneath next to mem.
Route fan wire under plate.
CPU board into shell.  2 screws on left of drive bay.  Post/stud into
center hole. (nothing under bottom sticker). Screw on right side of
docking bay connector.
Hard drive/battery shield under mainboard. 2 screws to CPU board.
CPU board, PSU.  Ensure tight fit on center flex connector and alignment with
plastic post by battery connectors.  Mic straight down onto retainer posts.
Screw in rear, screw next to PSU, and long screw in PSU.
Top shield/heatsink. Line up two tiny plastic posts.
PCMCIA-to-mainboard bridge.  Two screws. Press into flex connector.
PCMCIA-bracket into bridge by edge connector.  Four screws.
Battery holder onto PCMCIA-to-mainboard bridge.  Two screws.
Modem board into flex connector.  Shield over modem board and PCMCIA-to-mainboard bridge.  Six screws?
Modem module.  Two screws.
Memory module (2 screws).  Memory cover (2 screws).
CPU heatsink. 2 fan screws, 4 small heatsink screws, 3 mounting screws.  Bend front
bracket back into place, replace CPU shield, 2 screws (one on top of CPU, one underneath ribbon cable).  2 screws at CPU to drive bay area.
Sound board, fit into flex connector.  Attach ribbon cable into flip-up retainer.  Sound shield, 1 screw.
LCD.  5 screws under keyboard, 1 in rear by LPT port, 2 on bottom at rear, 2 under HDD. 4 wire harnesses, 1 ground wire.
Replace front panel.  4 screws in battery area. 2 screws in HDD area.